Truma Aventa Comfort not comfy now...!!!

Discussions about any 240V powered device ..., installation, faults, advice, TV\'s etc'
2foot6

Re: Truma Aventa Comfort not comfy now...!!!

Post by 2foot6 »

Maybe you should have gone to Bunnings if you wanted a sausage or gone to Spec 'Savers and read the book earlier :shock: :lol: Glad it has worked out for you,was the reset of the air unit or the remote?
User avatar
Vik351
Posts: 1230
Joined: Sat Aug 05, 2017 3:50 pm
Location: Adelaide SA

Re: Truma Aventa Comfort not comfy now...!!!

Post by Vik351 »

2foot6 wrote: Mon Dec 10, 2018 9:20 am Maybe you should have gone to Bunnings if you wanted a sausage or gone to Spec 'Savers and read the book earlier :shock: :lol: Glad it has worked out for you,was the reset of the air unit or the remote?
Onion danger at bunningtons...

The reset was on the unit, then you have to reset the remote once you have reset the unit so the reset remote can work the reset unit...

The fuse was blown at 6.3 and the bloke at Cararest rang trauma ant that bloke said “yea, the sixers blow at the drop of, so go for 8 amp slow blow SF2121 which I did

And me thinks what did it was, had the AC on 240 ,pulled the power lead out to move the Espie so the solar and inverter musta kicked in with a spike and poped the fuse...???

Lesson learned... the hard way...!!! :(

Vik... :mrgreen:
Merk 4x4 VF30 519 CDI 2020 LWB V6TD 3 ltr 6 wheeler ,Tenorite Grey ... yep, it's not white ...!!! 8-)
2foot6

Re: Truma Aventa Comfort not comfy now...!!!

Post by 2foot6 »

Unplugging the power lead when the air con was running and compressing the gases,depending on the delay of the inverter changeover,would mean the compressor would be trying to start against a large amount pressure,thus causing a much higher current draw which will blow fuses.Sounds feasible to me from prior experiences.........Peter.
User avatar
T1 Terry
Posts: 15962
Joined: Fri Nov 23, 2012 3:44 pm
Location: Mannum South Australia by the beautiful Murray River
Has thanked: 50 times
Been thanked: 30 times

Re: Truma Aventa Comfort not comfy now...!!!

Post by T1 Terry »

vik351 wrote: Mon Dec 10, 2018 8:48 am Well there ya go, when in doubt get the book out...!!!

Had a read, found there was a reset on the unit :D pushed that and all good,made a noise... :P

Re tuned the remote with it and now all is well ... for now, should make it to the car yard ...!!! ;)

Asked the same thing on GNF ,not even one sausage ...!!! :o :shock: :evil:

Vik... :ugeek:
Ahhh yes, the old "when all else fails, read the manual" trick, catches them every time. Something like this should be in all appliances viewtopic.php?f=21&t=5662&p=94023#p94023
A person may fail many times, they only become a failure when they blame someone else John Burrows
Those who struggle to become a leader, rarely know a clear direction forward for anyone but themselves
User avatar
Greynomad
Posts: 9025
Joined: Tue Dec 04, 2012 4:16 pm
Location: Rutherglen, Vic.
Has thanked: 28 times
Been thanked: 61 times

Re: Truma Aventa Comfort not comfy now...!!!

Post by Greynomad »

Every electrical/electronic item sold should carry a sticker on the 'ON' switch wot sez: "RTFM!!"
:D
Regards & God bless,
Ray
--
"Insufficient data for a meaningful answer."
Isaac Asimov, "The Last Question"

"I refuse to drink water, because of the disgusting things fish do in it"
W.C.Fields
2foot6

Re: Truma Aventa Comfort not comfy now...!!!

Post by 2foot6 »

A lot of electronic and electrical appliances do say read the manual,but some people don't bother or they need to go to specsavers.The OP should have read the manual :o :lol: :lol: A good learning experience Vik............Peter.
User avatar
Vik351
Posts: 1230
Joined: Sat Aug 05, 2017 3:50 pm
Location: Adelaide SA

Re: Truma Aventa Comfort not comfy now...!!!

Post by Vik351 »

You jokers got NFI...!!! :o

I was all a plan... SWMBO saw the grief I was in and the pain of 2K for a new unit... :x

BUT, as “I” fixed it ,that alotted foldinstuff could be now be used for a new dining table for the new humpy... :lol: :lol: :lol:

On order as I type... :twisted:

Vik... :mrgreen:
Merk 4x4 VF30 519 CDI 2020 LWB V6TD 3 ltr 6 wheeler ,Tenorite Grey ... yep, it's not white ...!!! 8-)
2foot6

Re: Truma Aventa Comfort not comfy now...!!!

Post by 2foot6 »

Vik,is it coming from IKEA,if it is READ THE MANUAL............ :o :shock: :D :idea: :roll: :) ;) .......Peter
User avatar
T1 Terry
Posts: 15962
Joined: Fri Nov 23, 2012 3:44 pm
Location: Mannum South Australia by the beautiful Murray River
Has thanked: 50 times
Been thanked: 30 times

Re: Truma Aventa Comfort not comfy now...!!!

Post by T1 Terry »

2foot6 wrote: Tue Dec 11, 2018 4:46 pm Vik,is it coming from IKEA,if it is READ THE MANUAL............ :o :shock: :D :idea: :roll: :) ;) .......Peter
Haven't you seen the Kit-Kat ad about the two bloke and the catapult construction, definitely a set of IKEA involved there :lol:
A person may fail many times, they only become a failure when they blame someone else John Burrows
Those who struggle to become a leader, rarely know a clear direction forward for anyone but themselves
User avatar
Vik351
Posts: 1230
Joined: Sat Aug 05, 2017 3:50 pm
Location: Adelaide SA

Re: Truma Aventa Comfort not comfy now...!!!

Post by Vik351 »

2foot6 wrote: Tue Dec 11, 2018 4:46 pm Vik,is it coming from IKEA,if it is READ THE MANUAL............ :o :shock: :D :idea: :roll: :) ;) .......Peter
The bloody table only came, and some other box with 4 firewood logs to burn, musta thought I still had an open fire ... 4 bolts as well...???

vik... :?:
Merk 4x4 VF30 519 CDI 2020 LWB V6TD 3 ltr 6 wheeler ,Tenorite Grey ... yep, it's not white ...!!! 8-)

Return to “240V discussions”