Cut of switch
-
Mrcoolabah1au
- Posts: 2699
- Joined: Wed Jan 23, 2013 3:36 pm
- Location: Tocumwal on the Murray river
Cut of switch
If I wanted to put some sort of switch to cut the power of for any number of reasons what type do you think I mite need
Coolabah1au
Wayne nini
Wayne nini
-
Dot
- Posts: 24720
- Joined: Fri Nov 23, 2012 6:12 pm
- Location: Strathalbyn SA
- Been thanked: 37 times
Re: Cut of switch
Be very careful how you answer this one Wayne 
Queen of the Banal & OT chatter and proud of it. If it offends you then tough titty titty bang bang.
-
Mrcoolabah1au
- Posts: 2699
- Joined: Wed Jan 23, 2013 3:36 pm
- Location: Tocumwal on the Murray river
-
Peter and Sandra
- Posts: 249
- Joined: Tue Dec 11, 2012 3:39 am
- Location: Dungog NSW
Re: Cut of switch
Wayne I use the marine style switches like this one.
http://www.ebay.com.au/itm/271990400005 ... EBIDX%3AIT
They are available in black or red, I've used three, one to disconnect the solar, one for the 12v power feed to the inverter and one is a master which cuts all 12v from the lithium bank.
Depending on the model/brand some allow the knob bit to be removed completely which stops anyone turning things back on accidentally.
http://www.ebay.com.au/itm/271990400005 ... EBIDX%3AIT
They are available in black or red, I've used three, one to disconnect the solar, one for the 12v power feed to the inverter and one is a master which cuts all 12v from the lithium bank.
Depending on the model/brand some allow the knob bit to be removed completely which stops anyone turning things back on accidentally.
Oka 4WD camper/motorhome, 1100w solar, 400ah lithium, diesel heating, HWS and cooking
-
bob r
- Posts: 3946
- Joined: Sun Dec 09, 2012 9:24 am
- Location: central west nsw Tiaro QLD for winter
- Has thanked: 3 times
- Been thanked: 4 times
Re: Cut of switch
Wane I have two off these they have been good so far.
http://www.ebay.com.au/itm/12V-24V-Key- ... 5d581274e4
http://www.ebay.com.au/itm/12V-24V-Key- ... 5d581274e4
-
homeless
- Posts: 838
- Joined: Fri Nov 30, 2012 6:26 pm
- Location: Somewhere on the Murray River
- Has thanked: 2 times
- Been thanked: 3 times
Re: Cut of switch
I have a switch wired into the control wire of the gigivacs. Open the circuit and the gigivac is OFF no power out or in.
Others will tell you if I am doing it right or not.
This makes it a low current switch and not a high current one so no spark etc and it is for me a safety switch as well for manual turn of if I want to select only one battery.
I have a 4x4 collision switch wired in as well before any control so in an event of a collision all my 240v is turned off and batteries disconnected.
To reset is just a matter of a lever to set all running again. so not sure if that is warranted but makes me feel more comfortable
Regards
Brian
Others will tell you if I am doing it right or not.
This makes it a low current switch and not a high current one so no spark etc and it is for me a safety switch as well for manual turn of if I want to select only one battery.
I have a 4x4 collision switch wired in as well before any control so in an event of a collision all my 240v is turned off and batteries disconnected.
To reset is just a matter of a lever to set all running again. so not sure if that is warranted but makes me feel more comfortable
Regards
Brian
12 × 5 house boat moored at the present in Mannum Waters Marina.
Converting to LiFePo4 for float alone status
Converting to LiFePo4 for float alone status
-
Mrcoolabah1au
- Posts: 2699
- Joined: Wed Jan 23, 2013 3:36 pm
- Location: Tocumwal on the Murray river
Re: Cut of switch
Like that idea ask terry when I see him next month he said he will wire up the new cell first then look at what is needed next ok 
Coolabah1au
Wayne nini
Wayne nini